Last Updated on September 25, 2024 by Adams
How To Use a Jump Starter Properly?
How To Use a Jump Starter Properly? If you own a vehicle, then possessing a portable jump starter is very much a must-have piece of technology. A portable jump starter makes it possible for you to have your battery up and running without depending on a stranger for assistance.
It is hard to anticipate when your vehicle will break down. Sometimes when you park your car, the battery just fails to start up. This is a stressful situation and one that experienced drivers are all too familiar with.
But the creation of portable and rechargeable jump starters has made it much easier to manage an emergency while on the go as technology grows and evolves. While the idea of this unit is the same as using conventional jumper cables, in addition to making this portable device operate properly, there are a few more key steps.
-
Safety First!
It is crucial to consider all proper safety measures before starting to use your portable jump starter to guarantee that you, your car battery, and your jump starter are all secured. As the use of electrical voltage is required to jump-start your vehicle, you must be cautious at all times.
However, do not worry, even though there are electrical risks involved with jump-starting your vehicle, it is perfectly secure to use a portable jump starter and thus is a low-risk process. Pay attention to the following precautionary measures for good practice before working with your portable jump starter:
- Before actually beginning the process of relaunching your battery, ensure your car and the jump starter are fully off.
- Take the keys out of the ignition to guarantee that initially, each component of the vehicle is turned off.
- Never attach or do not let the red(positive) and black(negative) clamps to be linked via an electrical conductor to one another.
- Please ensure during the procedure that there are no fluids or flammable objects near your vehicle or the jump starter.
Take each of the clamps of the jump starter cables in each hand while the car is still switched off. You should have one red and one black. Note never to put the two clamps together! This could induce a short circuit and stop the operation of the portable jump starter and consequently, you will still be stuck with a dead battery.
Hook up the red clamp to the positive terminal on your car’s battery, whilst also connecting the black clamp to a non-conductive component of secure metal in your vehicle. A good option is often the metal that holds up the hood of the vehicle.
-
Turning on the Jump Starter
Once you have verified that your cable clamps are in the correct position, you can move ahead to turn over your jump starter.
Keep in mind: Do not switch on your car’s ignition at this moment. In terms of facilitating the supply of power from the unit itself into your car’s battery, the jump starter should be switched on first.
-
Turning on Your Vehicle
The next step is to turn your car’s engine on. This should enable the jump starter to transfer Quick spurts of electricity in large quantities into the vehicle’s battery, which will usually start up pretty quickly. This however implies that cranking your engine for a long time will cease the jump starter from working.
You can just have the engine switched on for around five seconds each time. The jump starter comes to life as soon as your ignition on, sending a surge of voltage through your car’s battery.
The jump starter puts out the highest allowable amount of power at this level. To balance the strength of the gear, take full advantage of this by just switching on your engine in rapid succession.
If your engine has been cranked up for 5 seconds and the battery still is not starting, do not turn the ignition down for a long period. If anything, give it a decent break between tries for up to 3-5 minutes. If you proceed to grind the battery, you will strain out the jump starter, which can end up causing it to heat up or short-circuit, which would pose a hazard to your unit.
When the jump starter is prepared to give all of its power once more, make a further 5-second try at the engine. After some more attempts, your battery must kickstart!
-
Remove Your Cables
You must switch off your jump starter once your car has properly ignited. This will enhance the gear’s lifespan. Furthermore, must ensure to get it recharged as early as possible.
Recharging the lithium-ion battery of your jump starter as earlier as you can is advised, a fully charged battery at all times means that the gear has a better and long lifespan.
Once the jump starter is switched off you would then remove the jumper cables. Firstly, detach the black cable, then detach the red one. Put them all back in a secure place so you are not going to lose or damage them. Make sure to keep your vehicle running once it has efficiently been jump-started.
Recommended Readings (Rated Recommendation)